Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing happened? Glance into the tank, and you may see no water inside. Before you worry, rest assured that correcting this challenge is usually easy to accomplish. If you can’t do it yourself, you can always arrange toilet repair with an Expert plumber. Follow these tips to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first step is to verify that the water is flowing. If you or someone in your household recently did a toilet repair, you may have turned off the water first. Did you not realize you had to turn it back on? To see, turn the water shut-off valve on the wall to the rear of the toilet. If the valve was turned off, water ought to now start refilling the tank. If this fails to work, test the water at your sink or an alternative plumbing fixture. If nothing flows from the tap, you could possibly have a more substantial water supply issue. Call your water company to find out more. 

Reposition or Replace the Float Mechanism 

Older toilet designs use a float ball to gauge the water level as it rises in the tank. When the ball hits a certain height, the float arm it’s attached to stops the water flow. However, insufficient water could enter the tank if the ball is positioned improperly or the arm is faulty. To adjust the float ball, start by removing the toilet tank lid. Bend the float arm up just a little bit to alter where it sits in the tank. If this does not fix the problem, you may need to replace the whole float mechanism. You should be able to do this yourself by following the directions that come with the replacement parts, or you can hire a plumber for help. Just understand that float balls are old toilet design. You may prefer improved durability and efficiency if you upgrade the existing tank components or replace the toilet completely. 

Adjust the Fill Valve 

More recent toilets utilize a float cup in place of a float ball, coupled with a fill valve and water level rod. There may very well be no water in the toilet tank because the valve has slipped out of place or become plugged. Here are techniques to try: 

  • Modify the fill valve: Look inside the toilet and locate the fill valve on top of a vertical tube device on the left side of the tank. Make sure it’s secure and evenly ahered to the tube. Then, change the water level. Current models of toilets have an adjustment knob you can turn by hand, while older versions may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and allow the tank refill to verify the water level. Change it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
  • Clean the fill valve: Mineral buildup and other crud could be blocking the valve and keeping your toilet from filling. Shut down the water behind the toilet and remove the fill cap. Then, steadily turn the water back on, cupping your hand over the valve to stop water from spraying all over. After several seconds, turn the water back off. Finally, scrub the fill cap to remove hard water buildup. If the cap is broken, swap it out. 
  • Clean the valve tube: The tube below the fill valve could also be blocked. Shut off the water and take away the valve hardware. Then, stick a slim bottle brush or wire down the tube. Turn the water back on a little to flush away the debris. Replace the valve hardware and flush the toilet to test your work. 

Repair or Replace the Trip Assembly 

If you’ve followed the steps above without any luck, the one remaining possibility is a broken trip assembly. This element attaches the flush handle to the tank. If it’s not working or positioned inadequately, the flush cycle may not complete, leaving the tank empty. Remove the toilet tank lid and examine the trip assembly connected to the handle. If it’s out of place, reposition it. If the assembly is bent, worn or broken, replace it. Whether you complete the job yourself or leave it to a plumber, this uncomplicated repair should get your toilet tank filled with water once again. 

Schedule Toilet Repair Today 

You can’t go long without a functional toilet, so phone [Company name] to inquire about a toilet repair. We can figure out why your toilet isn’t filling and suggest the right fix. If your plumbing fixture is old and worn out, our team can easily install a high-efficiency toilet in your bathroom. Rest assured that every plumbing repair and replacement we conduct is backed by a 100% satisfaction guarantee. To schedule an evaluation from one of our licensed professionals, please reach out to your neighborhood Sunbeam Service Experts office today.